Over 2000 metal building prices posted on website!

OPTION A: BLOWOUT Deals - Pay only $500 Above Cost
OPTION B: Price Your Own Deal - Pay $800 Above Cost
OPTION C: We Quote - Pay 10% Above Cost

To Keep Our Prices At Cost, We Can Only Formally Quote Ready Buyers

Steelbuilding Specifications

Integrity Building Sales BBB Business Review

Smart buyers buy based on objective information such as written STEELBUILDING SPECIFICATIONS, QUOTED SAVINGS, AND a company's BETTER BUSINESS BUREAU RATING AND REVIEWS .

steelbuilding specifications

PRIMARY STEELBUILDING FRAMING

(Mainframes)

SOLID I-BEAM CONSTRUCTION

Material used is minimum 50,000 p.s.i. yield strength. (Some steelbuilding manufacturers use 35,000 p.s.i. yield strength material, which is not as strong). Frames are single bead, continuous submerged arc welded by automatic welding machines to help insure quality. A factory applied rust inhibiting primer is used to help protect the mainframes and secondary material during the erection process.

ENDWALL FRAMES AND COLUMNS

These components are either cold formed, hot-rolled or built-up “I” sections depending on design requirements.

SECONDARY FRAMING

GIRTS (in sidewall) and PURLINS (in roof) are minimum 8” to meet steelbuilding design requirements. Cold rolled Z-section, 12 to 16 ga ASTM A-653, 55,000 p.s.i. yield material is used to provide maximum strength.

Bypass girt system overlaps at sidewall columns forming a continuous “span” for extra strength. All girt clips are factory welded for easier erection.

PURLINS are top-mounted on the rafter with a varied lap of 1’6” to 5’ for strength and cost savings in erection labor. Maximum purlin spacing is 5’ on center.

EAVE STRUT is a cold-formed C-section that is rolled for the appropriate roof pitch to help insure weather tightness at the eave.

RAKE ANGLE is a 2x4 angle supplied for the attachment of the sheeting at the rake of the building for ease of installation.

BASE ANGLE is a 2x4 angle supplied for the attachment of the base of the sheeting to the concrete. The base angle is to be attached to the concrete with ram-sets or equivalent anchors.

BRACING All diagonal galvanized cable bracing is supplied for roof and walls to remove longitudinal load from the structure. Galvanized cable is used rather than solid rod to prevent the bracing from “sagging” under its own weight and it is easier to install. All cables are pre-stressed and pre made for easier erection.

Angle Flange Bracing is provided for the connection of the rigid frame to the purlins and girts. This insures the allowable compressions are adequate for any combination of loading.

FRAMED OPENINGS have cold-formed C-section jambs and headers to help insure easy installation of overhead doors, etc.

SHEETING

24 or 26 gage 80,000 P.S.I. yield strength material standard. Some steelbuilding manufacturers use a lower yield strength material, which is less resistant to damage from hail or other impacts. 40 year warranty on premium color finish on walls and trim. Roof finish is galvalume or premium colored finish.

ALL COIL STEEL has a minimum of G-90 class Galvalume substrate (1.25oz hot dipped) to help prevent deterioration of the steel sheeting.

DEEPER HIGH-RIB with more frequent corrugations provides extra strength.

OPTIONAL ARCHITECTURAL PANEL configuration is available for walls, mansard systems, soffit material, etc., to add an aesthetic appeal to your building.

FASTENERS

STRUCTURAL BOLTS meet requirements ASTM Standards.

A-325 for primary frame connections

A-307 for secondary framing

SELF-DRILLING AND SELF-TAPPING FASTENERS are pre-assembled with neoprene washers and metal caps to help insure weather tightness.

CLOSURES

CLOSED CELL NEOPRENE STRIPS are used to help seal building. Located at eave, gable, and optional at the base of building to help provide weather tightness. Pre-formed shapes to match panel configuration providing a tighter seal.

1-1/2” SHEETING NOTCH at base of concrete where panel site is designed into every building. Sheeting notch provides an air infiltration stop on blanket insulated building.

SEALANTS

SEALANT for roof sidelaps, endlaps and flashing at gable is provided to help insure weather tightness. Nominal 3/8” x 1/8” thick pressure sensitive tape sealant for ease of installation.

RIDGE CAP

LONG OVERLAP to help prevent water from siphoning into building.

TRIM AND FLASHING

All buildings are fully trimmed at rake (gable), corners, and eaves with standard trim material for a more finished look. This not only improves look of building, it is an additional deterrent to moisture, insects, and dirt from getting into the building.

STEELBUILDING PLANS AND DRAWINGS

ANCHOR BOLT setting plan, building reactions for foundation design, Erection Manual, and Engineer

Letter of Certification is provided shortly after receipt of deposit for steelbuilding.

ERECTION DRAWINGS provide step by step instructions for case of assembly by dealer or customer.

ENGINEER CERTIFIED APPROVAL DRAWINGS including wall and roof framing diagrams, crosssections, sheeting, and flashing details are provided. These drawings clearly show the proper erection and assembly of all building components.

ALL PARTS ARE NUMBERED A part number is placed on each component (not including sheeting,screws, etc.). These part numbers coincide with a detailed listing contained in the bill of materials that come with your building. They same numbers are also used on the drawings for clarity and to help with assembly on the jobsite.

Certifications of Major Manufacturer

Our supplier is recognized as a member of or accredited by the following standards organizations. Our clients can take pride in knowing their structures exceed the rigorous quality standards and guidelines specified by the associations listed below.

Metal Building Manufacturers Association (MBMA)
The MBMA has served as the voice of a large concerned manufacturer base for over 50 years. Founded in 1956, the MBMA requires that all its member companies abide by a strict code of industry standards that create and maintain the highest level of quality.

American Welding Society (AWS)
The AWS, a not-for-profit organization, has worked to continue the developmental efforts of the welding industry since its inception in 1919. The AWS represents and supports extended education from a scientific and technological standpoint in the welding community as well as others closely related: brazing, soldering, and other metal fusion processes.

International Accreditation Service, Inc.
The IAS lends confidence and security to an organization’s services and/or products. An IAS accreditation means the company in question meets and surpasses industry guidelines concerning durability and performance. The IAS recognizes our supplier as an approved fabricator of structural steel building assemblies.

Architectural Testing, Inc.
With regional laboratories across the United States, Architectural Testing conducts quarterly inspections of our manufacturer’s facility. The inspections encompass procedural reviews as well as overall compliance with the standards set by the American Welding Society, ensuring safe and secure metal buildings.

searching for steel buildings

Why Utilize Integrity Building Sales

1

No Upfront Cost! Integrity Building Sales posts and quotes its ‘actual’ wholesale cost FIRST for FREE!

2

You choose the profit amount to be added to IBS ‘actual’ cost.  Customer pays profit by close of business day.

3

Certified plans are completed in 10 -14 days. Standard building delivery in 8 weeks. Available 3 week building delivery.

4

IBS has been established since 2010 and maintains an A+ BBB grade. Major manufacturer is IAS certified and MBMA member.

5

Pay your deposit directly to certified manufacturer, not a broker! Quotes are guaranteed $500 below market quotes (40x60x14 and larger). Average savings $3,250!